SKU: KOL2736
Brand: Kolpin Powersports
The tilt mechanism is designed for cooling the airflow in warm temperatures.The open positions are designed for low-speed airflow only.The high-speed riding and trailering require the windshield to be in the full closed position.
IMPORTANT NOTICES
READ AND UNDERSTAND THESE INSTRUCTIONS COMPLETELY BEFORE INSTALLATION TO
AVOID INJURY TO YOURSELF, DAMAGE TO THE VEHICLE OR ACCESSORY.
DEALER
These instructions contain important information for future reference and must be given to the customer at time of purchase or upon completion of installation.
1. Installation
a) Find a clean flat area where you can safely lay down the windshield
(Item A). Partially remove the protective film on both sides and apply
the co-extruded bulb seal (Item B) to the lower lip using manual pressure
to ensure good adhesion to the windshield and cut any excess.
IMPORTANT NOTICES
Over-tightening any and/or all screws will cause cracks around mounting holes which is not covered by any
warranty
b) Partially remove the protective film on both sides and attach pivot components (Item E & F) to the windshield using supplied hardware (Item D) as shown. All screws that are passing through the windshield will be tightened later in step d). Do not over-tighten the screws that combine the slide arm with the lower pivot, those 2 parts need to swivel.
c) Attach clamps (Item C) to the roll cage of your vehicle using supplied hardware (Item D) as shown. The clamp sets must be installed with the threaded inserts aligned from right to left of the roll cage. Tighten only the 4 socket cap screws M6 x 45. Do not tighten the clamps to the roll cage at this stage; you will need to make adjustments later on.
IMPORTANT NOTICES
Torque specifications must be followed when tightening bolts.
Over-tightening any and/or all screws will cause cracks around mounting holes which is not covered by any
warranty.
IMPORTANT NOTICES
To prevent any parts failure during installation and/or removal, the upper windshield must ALWAYS be
properly supported by TWO people, one on each side, with one hand located on the lower edge and the other
by the upper pivot.
One person alone CANNOT install and/or remove the upper windshield without over-flexing and stressing
the material. This action may cause breakage and/or cracks to the windshield.
This is not covered by any warranty.
d) With TWO people, install the windshield to the vehicle by following instructions below.
1. Make sure that both upper clamps are at the same height.
2. Hold the windshield horizontally and slide it down by ensuring that both upper pivot cylinder adaptors are going through the upper pivot as per drawing #1.
3. Gently pull on the windshield as per drawing #2 towards the front of the vehicle for the
upper pivot to slide to the end onto the upper pivot cylinder adaptor.
4. Lower the windshield as per drawing #3 and the upper pivot will catch the second upper
pivot cylinder adaptor.
5. Adjust the height of the upper clamp first by ensuring the overall leveling.
6. Tighten all screws regarding the upper pivot.
7. Adjust the height of the clamp to the lower pivot and slide arm and use "T" knob to lock in place.
Drawing #4 shows the position you should have when windshield is closed
8. Tighten all remaining screws and nuts.
To operate the tilt mechanism :
1. Unlock by loosening both "T" knobs (without removing them).
2. From inside the cab, gently tilt out (both side at the same time) the windshield to the desired
position. Note that there are 3 pre-determined positions on the slide arm; closed, half-opened
and fully-extended
To remove the windshield
With TWO people, remove both "T" knobs and follow reverse instructions 4, 3 & 2 of step #d).
IMPORTANT NOTICES
The tilt mechanism is designed for cooling the airflow in warm temperatures. Note that any open positions
are designed for LOW-SPEED operation ONLY.
At HIGH SPEED RIDING or when TRANSPORTING the vehicle, the windshield must be CLOSED.
High speed running or trailering with windshield open may cause failure and is not covered by any
warranty.
2. Maintenance and Care
Tighten all hardware after first use and periodically thereafter.