Universal UTV Poly Roof Medium by Kolpin

220.49
Ask a question
$220.49

Availability: In Stock

Kolpin provides excellent sun shade and rain cover
Qty:
Add to Wishlist
Verify your product fitment.

SKU: 4450
Brand: Kolpin Powersports

Universal UTV Poly Roof Medium by Kolpin

The Universal UTV Roof (Medium) by Kolpin provides excellent sun shade and rain cover and will look like it came directly from the factory once installed. Its heavy duty construction will withstand the toughest conditions and handle the roughest of terrain. Installation is easy utilizing your vehicles existing mounting points.

Universal UTV Poly Roof Medium Features:

  • Provides excellent sun shade and rain cover
  • Easy installation requires drilling of the roof
  • All mounting hardware included
  • Sturdy and trailerable
  • Design is 4.0" narrower in front than the rear
  • Overlapping, 3-piece design offers stability and easy mounting to fit the most popular brands of utility vehicles
  • Adjustable side width - 49.0" to 55.0" front and  53.0" to 59.0" rear
  • Made in the U.S.A.
Warning: This product contains chemicals known to the State of California to cause cancer, birth defects, or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.

2017 Fitments

  • 2017 Gator XUV 550/560/590i

2016 Fitments

  • 2016 Gator XUV 625/825/855/HPX825
  • 2016 Gator XUV 550

2015 Fitments

  • 2015 RTV 900
  • 2015 RTV 500
  • 2015 RTV 400
  • 2015 Gator XUV 855
  • 2015 Gator XUV 550

2014 Fitments

  • 2014 Rhino 700
  • 2014 Ranger EV
  • 2014 Ranger 800 (Fullsize)
  • 2014 Ranger 400/500/570/800 (Midsize)
  • 2014 RTV 900
  • 2014 RTV 500
  • 2014 RTV 400
  • 2014 Gator XUV 855
  • 2014 Gator XUV 550

2013 Fitments

  • 2013 Rhino 700
  • 2013 Ranger EV
  • 2013 Ranger 800 (Fullsize)
  • 2013 Ranger 400/500/800 (Midsize)
  • 2013 RTV 900
  • 2013 RTV 500
  • 2013 RTV 400
  • 2013 Gator XUV 855
  • 2013 Gator XUV 825
  • 2013 Gator XUV 550

2012 Fitments

  • 2012 Rhino 700
  • 2012 Ranger 800
  • 2012 Ranger 400/500
  • 2012 RTV 900
  • 2012 RTV 500
  • 2012 RTV 400
  • 2012 Gator XUV 825
  • 2012 Gator XUV 625
  • 2012 Gator XUV 550

2011 Fitments

  • 2011 Rhino 700
  • 2011 Ranger EV
  • 2011 Ranger Diesel
  • 2011 Ranger 800
  • 2011 Ranger 400/500
  • 2011 RTV 900
  • 2011 RTV 500
  • 2011 Mule 4000/4010
  • 2011 Gator XUV 855
  • 2011 Gator XUV 825
  • 2011 Gator XUV 625

2010 Fitments

  • 2010 Rhino 700
  • 2010 Ranger EV
  • 2010 Ranger 800
  • 2010 RTV 500
  • 2010 Mule 4000/4010
  • 2010 Gator XUV 850D
  • 2010 Gator XUV 825
  • 2010 Gator XUV 620i

2009 Fitments

  • 2009 Gator XUV 620i

UniversalRoof Medium_4450_4451_1

Please read and understand these instructions completely before installation to avoid injury to yourself or damage to the vehicle
or accessory.
Dealer: These instructions contain important information for future reference and must be given to the customer at time of purchase or
upon completion of installation.

UniversalRoof Medium_4450_4451_2

Please Note: The Universal UTV Roof was designed to fit most UTV roll cages. Because roll cages may vary in size and design, use your
best judgement in determining where to locate the mounting hardware in order to provide a secure and stable installation.

1) Mount the four sets of clamps on the vehicle’s roll cage as
indicated in Image “A1”. Insert the tongue of the top clamp
into the groove of the bottom clamp and close the two halves
as indicated in Image “A2”. Please note the tabs of the
clamps may face inward or outward depending on your
vehicle’s roll cage.

2) Continue mounting the clamps on the vehicle’s frame by utilizing
the supplied M8 x 35mm lg. socket head cap screws, M8 serrated
lock washers and M8 nylock nuts as indicated in Image “A3”.
Do not tighten at this point. The clamps will need to be adjusted
before fully tightened

UniversalRoof Medium_4450_4451_3

3) Place the three panels of the roof onto the vehicle by sliding
the driver and passenger sides into the center panel as
shown in lmage “B”.
4) Continue sliding the two outside panels into the center panel
until the edges of the outer panels are snug with your
vehicle’s roll cage as shown in lmage “C”. At this point, make
certain the center panel is located in the center of the vehicle.
5) Fasten the two outside panels to the center panel by utilizing
the supplied M6 x 60mm lg. button head cap screws, M6 x
19mm O.D. bonded sealing washers, M6 x 25mm O.D. fender
washers and M6 nylock nuts as shown in lmage “D”. Repeat
this in all six holes located on the center panel. Do not tighten
at this point.
6) From inside the cab of your vehicle, locate the four clamps
mounted in Step 1 and Step 2. Slide them along the roll cage
until the slotted holes on the tongues of the clamps are
located in a position that will provide a secure and stable
mount for the roof.
7) From inside the cab of your vehicle, mark the four positions
through the slotted holes in the clamps as shown in lmage “E”

8) Slide the clamps to the side to provide room for a drill motor.
Using a 1/4” drill bit, CAREFULLY drill straight through the
bottom wall and top wall of the roof in all four positions as
shown in lmage “F”.
9) Using a 1/2” drill bit, CAREFULLY drill straight through the
BOTTOM WALL ONLY of the roof in all four positions as shown
in lmage “G1”. DO NOT DRILL THROUGH THE TOP WALL.
10) Insert the four supplied 12.7mm O.D. x 7.62mm I.D. x 25.4mm
thick white spacers into these four holes until they are
pressing up against the top wall as shown in lmage “G2”.
11) Return the clamps to their mounting position and finish
tightening them. Be sure not to overtighten.

UniversalRoof Medium_4450_4451_4

12) Fasten the outside roof panels to the rear clamps with
the supplied M6mm x 60 or M6 x 75mm screws, M6 x 19mm
O.D. bonded sealing washers, black spacer(s), M6 x 19mm
O.D. fender washers and M6 nylock nuts as shown in
lmage “H”. You are also provided with additional black
spacers to stack if you require more support on the clamps.
Please note the white spacers are placed between the two
walls of the roof to prevent it from compressing once
tightened. Do not tighten at this point.
13) Fasten the outside roof panels to the front clamps with
the supplied M6 screws, M6 x 19mm O.D. bonded sealing
washers, black spacer(s), M6 x 18mm O.D. fender washers
and M6 nylock nuts as shown in lmage “I”. You are also
provided with additional black spacers to stack if you
require more support on the clamps. Please note the white
spacers are placed between the two walls of the roof to
prevent it from compressing once tightened. Do not tighten
at this point.
14) Check to make sure the center panel is still located in the
center of the vehicle. You are now ready to secure all of
the mounting hardware. Be sure not overtighten. First,
tighten the hardware connecting the roof panels installed
in Step 5. Second, tighten the hardware connecting the
roof to the rear clamps installed in Step 12. Third, tighten
the hardware connecting the roof to the front clamps
installed in Step 13.

15) In order to stabilize the roof on the roll cage and to prevent
excessive vibration, you have been supplied with two selfadhesive
foam blocks. Using your best judgement, select
a size and cut to length. Remove the protective paper and
place between the front of the roof and the roll cage as shown
in lmage “J”.
16) Repeat this step for the back of the roof by selecting a size
and cutting to length. Remove the protective paper and place
between the back of the roof and the roll cage as shown in
lmage “J”.
17) Maintenance and Care: Tighten all hardware after first use
and periodically thereafter.

! WARNING

Failure to follow these installation
instructions completely may void any
warrantable components and result in property damage
or personal injury NEVER operate or transport UTV with
unsecured cargo. For additional assistance, please contact our
customer service department at:

 UniversalRoof Medium_4450_4451_5

 

Only registered users can write reviews. Please, log in or register

* Required Fields