Polaris Ranger Midsize 400/500 2 Inch Lift Kit by SuperATV

124.95
Ask a question
$124.95

Availability: In Stock

This lift kit is an easy, bolt-on system that when installed with stock tires and wheels increases your front and rear ground clearance by about 2" on average
Verify your product fitment.

* Required Fields

$124.95
Qty:
Add to Wishlist

SKU: LK-P-RAN400-2
Brand: SuperATV

Polaris Ranger Midsize 400/500 2-IN Lift Kit

Upgrade your machine with a SuperATV 2" lift kit. This lift kit is an easy, bolt-on system that when installed with stock tires and wheels increases your front and rear ground clearance by about 2" on average. When combined with larger tires and wheels your machine becomes even more EXTREME. Perfect for any type of riding, whether you are on the trails, farm, hills, creek, or sand. You are sure to stand out and out perform.

SuperATV lifts are carefully machined to maintain proper angles on the quad and are engineered for maximum performance with enhanced handling and stability. Components are precision cut and zinc plated for extreme durability.

Polaris Ranger Midsize 2-IN Lift Kit Features:

  • Front and Rear Lift
  • Zinc Plated for Extreme Durability
  • Room for Larger Tires
  • Complete with all necessary hardware and easy-to-follow instructions

2014 Fitments

  • 2014 Ranger 400/500/570/800 (Midsize)

2013 Fitments

  • 2013 Ranger 400/500/800 (Midsize)

2012 Fitments

  • 2012 Ranger 400/500

2011 Fitments

  • 2011 Ranger 400/500

2010 Fitments

  • 2010 Ranger 400/500

PolarisRanger_LiftKit_LK-P-RAN400-2_1

Front:

Do not tighten hardware completely unless noted. Keep all components removed from machine.

1. Raise machine off ground, secure with jack stands, remove Wheels and Inner Fenders.
2. Disconnect Tie-Rods from Struts. See Fig. 1.
3. Use straps to support A-Arms and remove Shocks from Shock Mount. See Fig. 1.
4. Remove stock Grommet. See Fig. 1a.
5. Install Lift Spacer (B) onto Strut as shown in Fig. 2.
6. Install stock Grommet onto Lift Spacer (B) as shown in Fig. 2a.
7. Place Strut/Lift Spacer (B) assembly through Shock Mount and reinstall stock components as shown
in Fig. 2b.
- Secure with hardware included with Lift Spacer (B).
8. Repeat steps for opposite side and tighten hardware completely.
9. Reinstall and trim Inner Fender Wells as shown in Fig. 3 to relieve stress on Brake Line.

PolarisRanger_LiftKit_LK-P-RAN400-2_2

 

PolarisRanger_LiftKit_LK-P-RAN400-2_3

Rear:

Do not tighten hardware completely unless noted. Keep all components removed from machine.

1. Raise Cargo Bed and disconnect Wiring Harness. See Fig. 4. Note: completely removing Cargo Bed
makes for fastest installation.
2. Raise rear of machine off ground, secure with jack stands, remove Wheels, and disconnect Sway Bar.
3. Remove Shocks from top of Frame and lean inward.
4. Install Rear Brackets (A) to Frame with provided M10-1.50 x 65mm Lg. HHCS, M10-1.50 Nylock
Nuts, M10 Flat Washers, and Spacers. See Figs. 5 - 5a.
5. Reinstall Shocks with stock hardware.
6. If reinstalling Sway Bar, flip over and secure with stock hardware. See Fig. 6.
7. Tighten all hardware completely and reinstall necessary components.

PolarisRanger_LiftKit_LK-P-RAN400-2_4

PolarisRanger_LiftKit_LK-P-RAN400-2_5

 

 

 

Only registered users can write reviews. Please, log in or register

* Required Fields