Polaris Ranger Full Size/Profile Tubing Half Fixed Windshield-GP by Kolpin

156
Ask a question
$156.00

Availability: In Stock

Windshield is cut with superior CNC 5-Axis Router.177" General Purpose Polycarbonate. Does NOT have scratch resistant finish.
Qty:
Add to Wishlist
Verify your product fitment.

SKU: 2633
Brand: Kolpin Powersports

Polaris Ranger Full Size Profile Tubing models 2013-current Half Fixed Windshield-GP by Kolpin.

Half Fixed Windshield-GP Feature:

  • Windshield is cut with superior CNC 5-Axis Router.
  • All edges are super-smooth.
  • Steel clamps with nylon injected turn knobs.
  • All hardware (nuts & bolts) are stainless steel with black-coated finish.
  • Easy to install, No drilling required.
  • Comes complete with all mounting hardware & detailed instructions.
  • .177" General Purpose Polycarbonate.
  • Does NOT have scratch resistant finish.
Warning: This product contains chemicals known to the State of California to cause cancer, birth defects, or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.

2018 Fitments

  • 2018 Ranger XP 900
  • 2018 Ranger Crew 900

2017 Fitments

  • 2017 Ranger XP 1000
  • 2017 Ranger XP 1000
  • 2017 Ranger XP 900
  • 2017 Ranger Crew 900

2016 Fitments

  • 2016 Ranger XP 900
  • 2016 Ranger XP 570 (Fullsize - Profile Bars)
  • 2016 Ranger Crew XP 570 (Fullsize)
  • 2016 Ranger Crew Diesel
  • 2016 Ranger Crew 900

2015 Fitments

  • 2015 Ranger XP 900
  • 2015 Ranger Crew 900
  • 2015 Ranger 570 (Full Sized)

2014 Fitments

  • 2014 Ranger XP 900

2013 Fitments

  • 2013 Ranger XP 900

2633-1

IMPORTANT NOTICES
`
READ AND UNDERSTAND THESE INSTRUCTIONS COMPLETELY BEFORE INSTALLATION TO AVOID INJURY TO YOURSELF, DAMAGE TO THE VEHICLE OR ACCESSORY.

      • For proper installation, TWO people are required.
      • Torque specifications must be followed when tightening bolts. Over-tightening any and/or all screws will cause cracks around mounting holes which is not covered by any warranty. 
      • As specified on carton label, once protective film on shields is removed, product cannot be returned.
      • As specified on carton label, damage caused by packaging staples is not covered by warranty. All staples must be removed prior to removing product from carton.
      • Failure to follow these installation instructions completely may void any warrantable components and result in product damage or personal injury.
      • Do not use Loctite or any other similar fastener adhesive. These types of products react to plastics and cause cracking. Not covered by any warranty.
      • Our windshields are made from the highest quality material providing optimum transparency and clarity. 

Blurriness and/or extrusion marks may or may not appear when looking through windshield from a wide, sideangle. This is normal for all extruded clear plastic materials.

      • The application of improper cleaners, abrasive and/or dirty cleaning towels can severely damage the product. Failure to follow cleaning recommendation (provided herewith) may void any warrantable components.

DEALER

These instructions contain important information for future reference and must be given to the customer at time of purchase or upon completion of installation.

 Parts List (parts available with kit only and not available separately)

2633-2

1. Installation

a) Temporarily remove the OEM plastic retaining clips (2) from the vehicle dash. These will be reused to complete the installation.

                                                                                   2633-1

b) To apply the co-extruded bulb seal (Item B) to the windshield (Item A), find a clean flat area where you can lay down the windshield. Partially remove the protective film on both sides and apply the co-extruded bulb seal starting just below the windshield upper bend using manual pressure to ensure good adhesion. The seal has an internal steel wire structure; a wire cutter is required to cut any extra length.

2633-4

c) Install the windshield to the vehicle using supplied hardware (Item C). Adjust the position of the windshield and tighten.

2633-5

2. Maintenance and Care

      • Tighten all hardware after first use and periodically thereafter.

CLEANING:

      • Rinse with lukewarm water; wash gently with mild soap or detergent and lukewarm water, using a soft cloth or sponge. DO NOT SCRUB
      • or use brushes or squeegees.
      • Rinse again. Dry with soft cloth or moist cellulose sponge to prevent water spotting.
      • To remove wet paint, glazing compound or grease, rub lightly with a good grade of VM&P naphtha or isopropyl alcohol, then wash and
      • rinse. DO NOT USE GASOLINE.
      • NOTICE: Abusive cleaning procedures by hand washing or automated washing equipment will eventually result in visual hazing, loss of
      • light transmission and coating delamination.
      • Compatible Cleaning Agents
      • Aqueous Solution of Soaps and Detergents
      • Joy Freon T.F. Palmolive liquid Top Job VM&P grade Naphtha Windex (with ammonia D)

MINIMIZING HAIRLINE SCRATCHES
For minimizing scratches and minor abrasions, mild automobile polish can be used.
Recommended products: Johnson Paste Wax, Novus Plastic Polish #1 and #2, Mirror Glaze plastic polish and Plexux1.
Testing polish on a separate Lexan sample is recommended. Be sure to follow product instructions carefully.

Only registered users can write reviews. Please, log in or register

* Required Fields