Can Am Maverick Half Fixed Windshield GP by Kolpin

134.57
Ask a question

Regular Price: $149.52

Special Price $134.57

Availability: In Stock

.177" General Purpose Polycarbonate & extremely durable rubber cushioned loop clamps
Qty:
Add to Wishlist
Verify your product fitment.

SKU: KOL2710
Brand: Kolpin Powersports

Maverick Half Fixed Windshield by Kolpin

Maverick Half Fixed Windshield Features:

  • .177" General Purpose Polycarbonate
  • Does NOT have scratch resistant finish
  • Easy Installation..No drilling required
  • Extremely durable rubber cushioned loop clamps
  • All hardware (nuts & bolts) are stainless steel with black-coated finish... No Rust!!
  • Comes complete with all mounting hardware & detailed instructions
  • Trailerable
  • For use on your Can-Am Maverick,please see application guide for model specifics
Warning: This product contains chemicals known to the State of California to cause cancer, birth defects, or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.

2017 Fitments

  • 2017 Maverick
  • 2017 Maverick Max

2016 Fitments

  • 2016 Maverick
  • 2016 Maverick Max

2015 Fitments

  • 2015 Maverick
  • 2015 Maverick Max

2014 Fitments

  • 2014 Maverick
  • 2014 Maverick Max

2013 Fitments

  • 2013 Maverick

2710_1

READ AND UNDERSTAND THESE INSTRUCTIONS COMPLETELY BEFORE INSTALLATION TO AVOID INJURY TO YOURSELF,

DAMAGE TO THE VEHICLE OR ACCESSORY.

  • FOR PROPER INSTALLATION, TWO PEOPLE ARE REQUIRED.
  • TORQUE SPECIFICATIONS MUST BE FOLLOWED WHEN TIGHTENING BOLTS.
  • AS SPECIFIED ON CARTON LABEL, ONCE PROTECTIVE FILM ON SHIELDS IS REMOVED, PRODUCT CANNOT BE RETURNED.
  • AS SPECIFIED ON CARTON LABEL, DAMAGE CAUSED BY PACKAGING STAPLES IS NOT COVERED BY WARRANTY. ALL STAPLES MUST BE REMOVED PRIOR TO

REMOVING PRODUCT FROM CARTON.

  • FAILURE TO FOLLOW THESE INSTALLATION INSTRUCTIONS COMPLETELY MAY VOID ANY WARRANTABLE COMPONENTS AND RESULT IN PRODUCT DAMAGE

OR PERSONAL INJURY.

  • DO NOT USE LOCKTITE OR ANY OTHER SIMILAR FASTENER ADHESIVE. THESE TYPES OF PRODUCTS REACT TO PLASTICS AND CAUSE CRACKING. NOT

COVERED BY WARRANTY.

  • OUR WINDSHIELDS ARE MADE FROM THE HIGHEST QUALITY MATERIAL PROVIDING OPTIMUM TRANSPARENCY AND CLARITY. BLURRINESS AND/OR
  • EXTRUSION MARKS MAY OR MAY NOT APPEAR WHEN LOOKING THROUGH WINDSHIELD FROM A WIDE, SIDE-ANGLE. THIS IS NORMAL FOR ALL EXTRUDED

CLEAR PLASTIC MATERIALS.

  • THE APPLICATION OF IMPROPER CLEANERS, ABRASIVE AND/OR DIRTY CLEANING TOWELS CAN SEVERELY DAMAGE THE PRODUCT. FAILURE TO FOLLOW
  • CLEANING RECOMMENDATIONS (PROVIDED HEREWITH) MAY VOID ANY WARRANTABLE COMPONENTS.

DEALER
These instructions contain important information for future reference and must be given to the customer at time of purchase or upon completion
of installation.

2710-1

1. Installation a) To apply the co-extruded bulb seal (Item B) to the windshield (Item A), find a clean flat area where you can lay down the windshield. Partially remove the protective film on both sides and apply the co-extruded bulb seal using manual pressure to ensure good adhesion. (the seal has an internal steel wire structure, a wire cutter is required)

2710-3

b) Install the windshield to the vehicle using supplied hardware (Item C). Adjust the position of the windshield and tighten. Caution: over tightening any hardware could cause irreversible damage to the windshield.

2710-4

CLEANING:

  • Rinse with lukewarm water; wash gently with mild soap or detergent and lukewarm water, using a soft cloth or sponge. DO NOT SCRUB or use brushes or squeegees.
  • Rinse again. Dry with soft cloth or moist cellulose sponge to prevent water spotting.
  • To remove wet paint, glazing compound or grease, rub lightly with a good grade of VM&P naphtha or isopropyl alcohol, then wash and rinse. DO NOT USE GASOLINE.

NOTICE: Abusive cleaning procedures by hand washing or automated washing equipment will eventually result in visual hazing, loss of

  • light transmission and coating delamination.
  • Compatible Cleaning Agents

Aqueous Solution of Soaps and Detergents

Joy Freon T.F. Palmolive liquid Top Job VM&P grade Naphtha Windex (with ammonia D)

MINIMIZING HAIRLINE SCRATCHES

For minimizing scratches and minor abrasions, mild automobile polish can be used.
Recommended products: Johnson Paste Wax, Novus Plastic Polish #1 and #2, Mirror Glaze plastic polish and Plexux1.
Testing polish on a separate Lexan sample is recommended. Be sure to follow product instructions carefully.

Only registered users can write reviews. Please, log in or register

* Required Fields