Kawasaki MULE 4000/4010 Laminated Glass Windshield by EMP

488.99
Ask a question
$488.99

Availability: Ships in 3-5 Days

The top portion is laminated glass and the lower vent portion is Hard Coated Polycarbonate
Qty:
Add to Wishlist
Verify your product fitment.

SKU: 13077
Brand: Extreme Metal Products

Kawasaki MULE 4000/4010 Laminated Glass Windshield by EMP

Now,you can have an Automotive style Laminated Glass Windshield on your MULE 4010.The top portion is laminated glass and the lower vent portion is Hard Coated Polycarbonate.The vent adjusts to three positions including fully closed.Once,installed it can be removed without any tools.Therefore,pictures are a representation of the product you will be getting but may vary due to product revisions.

Kawasaki MULE 4000/4010 Laminated Glass Windshield Features:

  • Laminated Safety Glass
  • Vents allow air flow on hot days
  • Tool-Less Removal once installed
  • DOT Rated and etched
  • Hard Coated Polycarbonate Vent
  • Allows access to the front storage compartment
Warning: This product contains chemicals known to the State of California to cause cancer, birth defects, or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.

2017 Fitments

  • 2017 Mule 4000/4010

2016 Fitments

  • 2016 Mule 4000/4010

2015 Fitments

  • 2015 Mule 4000/4010

2014 Fitments

  • 2014 Mule 4000/4010

2013 Fitments

  • 2013 Mule 4000/4010

2012 Fitments

  • 2012 Mule 4000/4010

2011 Fitments

  • 2011 Mule 4000/4010

2010 Fitments

  • 2010 Mule 4000/4010

2009 Fitments

  • 2009 Mule 4000/4010

Mule 4010 Glass Windshield

PIN: 13077 

Includes:

1. (1) Metal Frame with Glass (10549)

2. (1) Hard Coated Polycarbonate (13077-02)

3. ( 1) 44" Long Piano Hinge ( 12114 )-Black 

Hardware Kit:

I. (8) 1-3/4 Clamp w/Thumbscrews (988 I)

2. (2) Tip Out Brackets (RH & LH)(l 3077-03)

3. (10) 10-32 x 3/4" Long Phillips Screws

4. (10) 10-32 Nylon Nuts

5. (4) 1/4-20 x 3/4" Black Bolts -Black

6. (6) 1/4-20 Nylon Nuts

7. (2) 1/4" Nylon Washers -White

8. (2) L-Shaped Brackets (11215-15)

9. (4) 1/4" ID x 1-1/4" OD Black Washers

10. (2) Rubber Screw Caps .234" x .5" Lg

11. (2) 3/16" x 18" Bubble Edge Trim

12.(1) 1/8x l"x 12"AdhesiveBackedFoam

13.( 1) Logo Sticker

Tools Required:

1. Phillips Screwdriver.

2. 7/16" Wrench

3. l O MM Wrench

4. 3/8" Wrench

5. A Friends hands.

Mule 4010_Glass Windshield_13077_1

lnstallation:

1. Bolt the hinge to the metal frame and the poly bottom using the 10-32 screws and nuts. Do not to over-tighten the screws as it could crack the poly. (see fig. I)

2. Remove the thumbscrews and nylon nuts from the clamps. Set aside for now.

3. Using the (6) thumbscrews and (6) clamps attach the assembly to the cage. The thubscrews will go through the metal frame and into the clamps. Once you have it in the correct location you can put the nylon nuts on the clamps. You will probably need a hand with this step. The clamps are designed to remain on the cage at all times. You can remove the windshield by simply removing the thumbscrews.

4. Bolt the L-Shaped brackets to the Poly bottom using the large washers, 1/4-20 x 3/4 bolts, and nylon nuts. The leg of the bracket will point towards the center of the vehicle. (see fig. 3 and 4)

5. Attach the stainless steel Tip Out Brackets to the L-Shaped brackets using the nylon nuts. The Nylon washer will go between the part as act as a bearing. (see Fig 4 and 5).

6. Attach the clamps to the cage and tip out bracket using the remaining (2) clamps and (2) thumbscrews). You will need to put the nylon nuts on the clamps before operating the tip out bottom.

7. Apply the l" wide foam to the center of the bottom.

8. Slide the bubble edge trim over the bottom in two places as shown. (see fig. 6)

Mule 4010_Glass Windshield_13077_2

Mule 4010_Glass Windshield_13077_3

Mule 4010_Glass Windshield_13077_4

Mule 4010_Glass Windshield_13077_6

Mule 4010_Glass Windshield_13077_7

Mule 4010_Glass Windshield_13077_9

Only registered users can write reviews. Please, log in or register

* Required Fields