John Deere XUV/ HPX Gator Full Front Windshield by Kolpin

435.74
Ask a question

Regular Price: $472.49

Special Price $435.74

Availability: In Stock

You also have the ability to quickly remove the windshield without tools in just seconds.
Qty:
Add to Wishlist
Verify your product fitment.

SKU: 2900
Brand: Kolpin Powersports

John Deere XUV/ HPX Gator Full Front Windshield by Kolpin

The John Deere Gator HPX/XUV Windshield by Kolpin protects you and your passengers from the elements.You also have the ability to quickly remove the windshield without tools in just seconds.This is the toughest windshield available made from the best materials on the market!

John Deere XUV/ HPX Gator Full Front Windshield Features:

  • New Design
  • 1/4” abrasive-resistant GE Lexan MR10
  • Extremely durable injection molded clamps
  • All stainless steel,black coated finish hardware
  • Easy installation
  • Full Windshield-hinged for underhood access only

Windshield tilts only to access under hood area,it is NOT designed to be driven in the open position!

Warning: This product contains chemicals known to the State of California to cause cancer, birth defects, or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.

2015 Fitments

  • 2015 Gator XUV 825

2014 Fitments

  • 2014 Gator XUV 825 S4

2013 Fitments

  • 2013 Gator XUV 825

2012 Fitments

  • 2012 Gator XUV 825
  • 2012 Gator XUV 625

2011 Fitments

  • 2011 Gator XUV 855
  • 2011 Gator XUV 625

2010 Fitments

  • 2010 Gator XUV 850D
  • 2010 Gator XUV 620i

2009 Fitments

  • 2009 Gator XUV 850D
  • 2009 Gator XUV 620i

2008 Fitments

  • 2008 Gator XUV 850D
  • 2008 Gator XUV 620i

2007 Fitments

  • 2007 Gator XUV 850D
  • 2007 Gator XUV 620i

2900_22_1

Please read and understand these instructions completely before installation to avoid injury to yourself, damage to the vehicle or accessory. 

                                                Be certain to follow all specifications.  For proper installation, two people are required 

Dealer:  These instructions contain important information for future reference and must be given to the customer at time of purchase or 

                                  upon completion of installation.  Torque specifications must be followed when tightening bolts. 

2900_1

1. Installation

a) To apply the edge guard (Item C) to the windshields (Item A/B), find

a clean flat area where you can lay down both windshields.  With an

extreme caution, partially remove the protective film and apply the edge

guard (Item D) using manual pressure to ensure good adhesion to both windshields. 

2900_2             2900_4        2900_3

b) Attach pivot components (Item F) to lower windshield with supplied hardware as follows.  All screws that are passing through the windshield will be tightened later in step f).   Do not over-tighten the screws that combine the slide arm with the lower pivot, these 2 parts need to swivel.

2900_5               2900_6

c) Assemble all hinges (Item D) to lower and upper windshield (Item A & B) as per drawings. 

2900_7                 2900_8

d) Attach clamps (Item E) to the roll cage of your vehicle as per drawings.  Attention; all

clamps are not installed the same way.  Do not tighten at this stage; you will need to

make adjustments later on. 

2900_9      2900_10

                                                                                                                                                              2900_11

e) Install windshield to top clamps only, using 2 M6 x 16 knobs as shown.  Adjust height position and level of the windshield to ensure good fit with the hood.  Tighten both knobs and top clamps only with specified torque indicated below. 

2900_12          2900_13      2900_14

f) Adjust all remaining clamp positions and tighten all screws with specified torque indicated.  Ensure that the windshield is perfectly level before tightening.  If the windshield isn’t level, windshield functions will be affected.  Over-tightening clamps to roll cage could cause parts failures.

2900_15      2900_16      2900_17

To operate the tilt mechanism:

Simply loosen both ‘T’ knobs (without removing them) and push on the lower windshield from the inside of the cab until the desired position is reached.  Then tighten knobs.  Note that there are 3 pre-determined positions on the slide arm; closed, half-opened and fullyextended. 

  •  The tilt mechanism is designed for cooling the airflow in warm temperatures.
  •  Note that any open positions are designed for low-speed operation ONLY. 
  •  At high speed riding or when transporting the vehicle, the windshield must be closed. 

              2900_18   2900_19       2900_20

To open vehicle hood: 

Remove both ‘T’ knobs and fold the lower windshield upward as per picture. 

  •  Note that this position is not for riding but only to provide access to storage room under the hood. 

                                                                                                                                                                                 2900_21

3.  Maintenance and Care 

Tighten all hardware after first use and periodically thereafter.

Only registered users can write reviews. Please, log in or register

* Required Fields