Can Am Commander Flip Windshield - Scratch Resistant by SuperATV

449.95
Ask a question
$449.95

Availability: In Stock

Each Can Am Commander Flip Windshield has a super tough, scratch-resistant polycarbonate construction to help maximize durability and avoid degraded visibility caused by branches or debris! With a full-length bottom seal that’s contoured to your ride's design, this attractive flip windshield will provide you with great visibility and increased air-flow!
Qty:
Add to Wishlist
Verify your product fitment.

SKU: FWS-CA-COM-001-70
Brand: SuperATV

Can Am Commander Flip Windshield - Scratch Resistant by SuperATV

This Can Am Commander Flip Windshield is made from 1/4-inch polycarbonate for increased durability. It can be used with both hard and soft tops and adjusts to allow you to control the amount of visibility, protection, and air flow allowed by the windshield.

Protect passengers from debris, control air flow for comfort, and gain greater visibility using this Can Am Commander Flip Windshield. Maximum scratch resistant surface allows you to use this windshield for years.

Can Am Commander Flip Windshield - Scratch Resistant Features:

  • 1/4" AR abrasion resistant polycarbonate
  • Windshields are hard coated on both sides for extreme durability
  • Protects against chemical and UV attack
  • Contoured to hood with full-length rubber seal for a great fit
  • Easy to install – comes with all necessary hardware and instructions
  • Can be used with soft or hard tops
Warning: This product contains chemicals known to the State of California to cause cancer, birth defects, or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.

2017 Fitments

  • 2017 Commander 800/1000

2016 Fitments

  • 2016 Commander 800/1000

2015 Fitments

  • 2015 Commander 800/1000

2014 Fitments

  • 2014 Commander 800/1000

2013 Fitments

  • 2013 Commander 800/1000

2012 Fitments

  • 2012 Commander 800/1000

2011 Fitments

  • 2011 Commander 800/1000

Can-Am Commander Scratch Resistant Flip Windshield_FWS-CA-COM-001_1

 

 

Can-Am Commander Scratch Resistant Flip Windshield_FWS-CA-COM-001_12

Use hand tools only when assembling.

Do not use power tools.

- When assembling, do not tighten hardware completely.
- SuperATV has found that installing components to
windshields on a workbench, as shown in illustrations,
makes for easiest installation.

Windshield Cleaning:
- Do not use a dry cloth, or your hands, to wipe off Windshield; Scratching will occur.
- Do not use window cleaning fluids (Windex, 409, etc) or any solvents (gasoline, denatured alcohol, acetone, etc).
- Never use abrasive cleaners, abrasive pads, or gritty cloths.
1. Thouroughly rinse Windshield to float off dirt and mud.
2. Using a soft cloth, or microfiber cloth, clean Windshield with warm water and a gentle detergent. Baby shampoo or hand
washing soap are recommended.
3. To prevent water spots, use a chamois and blot Windshield dry.
Use hand tools only when assembling.
Do not use power tools.
- When assembling, do not tighten hardware completely.
- SuperATV has found that installing components to
windshields on a workbench, as shown in illustrations,
makes for easiest installation.

 

 

 

Can-Am Commander Scratch Resistant Flip Windshield_FWS-CA-COM-001_2

 

To ease installation, soak Seal in hot water before cutting or installing to increase flexibility.

 

- Install (2) Clamps (F) to Lower Windshield (B) with hardware shown.

- Install provided Hood Seal to Lower Windshield (B).Can-Am Commander Scratch Resistant Flip Windshield_FWS-CA-COM-001_2

 

 

 

- Install Catch, part of Latch Assembly (D), to Lower Windshield (B); place Latch Support (J) on bottom
section of Lower Windshield (B) and secure with hardware shown.

Can-Am Commander Scratch Resistant Flip Windshield_FWS-CA-COM-001_4

- Install Lower Windshield (B) to Roll Cage with bolts included with Clamps (F).

- Install provided Gasket to Lower Windshield (B).

Can-Am Commander Scratch Resistant Flip Windshield_FWS-CA-COM-001_13

 

 

- Install Handle and Support, part of Latch Assembly (D), to Upper Windshield (A) with hardware shown. 

Can-Am Commander Scratch Resistant Flip Windshield_FWS-CA-COM-001_5

 

- Install Pivot Block (E) to Upper Windshield (A) with hardware shown.
- Install Clamp (F) and Upper Support R (L) to Pivot Block (E) with hardware shown.
- Repeat for opposite side.

Can-Am Commander Scratch Resistant Flip Windshield_FWS-CA-COM-001_6

- Install Clamp (F) and Gas Strut (C) to Support (K).
- Repeat for opposite side.

Can-Am Commander Scratch Resistant Flip Windshield_FWS-CA-COM-001_7

 

- Place Upper Windshield assembly onto machine and secure to Roll Cage with Clamps (F).
- Open Upper Windshield and secure Gas Struts (C) to Pivot Blocks (E) with hardware shown.

Can-Am Commander Scratch Resistant Flip Windshield_FWS-CA-COM-001_8

 

- Close Upper Windshield and engage Latch

- Align Windshield assembly to machine making sure that Seal, on Lower Windshield (B), is in
contact with Hood.
- Tighten hardware completely.

 

Can-Am Commander Scratch Resistant Flip Windshield_FWS-CA-COM-001_9

 

Can-Am Commander Scratch Resistant Flip Windshield_FWS-CA-COM-001_1 10

Only registered users can write reviews. Please, log in or register

* Required Fields