Arctic Cat Prowler Full-Tilting Windshield by Kolpin

472.49
Ask a question

Regular Price: $524.99

Special Price $472.49

Availability: In Stock

This is the toughest windshield available made from the best materials on the market!
Qty:
Add to Wishlist
Verify your product fitment.

SKU: 2455
Brand: Kolpin Powersports

How to pick a windshield for your UTV

Arctic Cat Prowler Full-Tilting Windshield by Kolpin

The Arctic Cat Prowler Full-Tilting Windshield by Kolpin protects you and your passengers from the elements.This versatile windshield incorporates a three-position tilt mechanism allowing you to adjust it from fully closed,to half extended,to fully extended. You also have the ability to quickly remove the top panel,creating a convenient half windshield.This is the toughest windshield available made from the best materials on the market!

Arctic Cat Prowler Full-Tilting Windshield Features:

  • Features a three-position til mechanism to control airflow
  • Constructed of ultra-thick,high-quality,scratch-resistant 1/4" MR10 GE Lexan polycarbonate
  • Super-smooth edges and custom bend design provides maximum rigidity
  • Custom injection-molded nylon mounting brackets
  • All stainless steel,black-coated finish hardware
  • Fits entirely between the roll bars
  • Easy to install and no drilling required
  • Note:This windshield fits cages with round tubes

Note: Open positions are designed for low-speed airflow ONLY. High-speed riding or trailering require the windshield to be in the FULL CLOSED position.

Warning: This product contains chemicals known to the State of California to cause cancer, birth defects, or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.

2011 Fitments

  • 2011 Prowler 1000
  • 2011 Prowler 550/700

2455_1

                               Please read and understand these instructions completely before installation to avoid injury to yourself, damage to the vehicle or accessory.

                                                                        Be certain to follow all specifications. For proper installation, two people are required
                                    Dealer: These instructions contain important information for future reference and must be given to the customer at time of purchase or

                                                                     upon completion of installation. Torque specifications must be followed when tightening bolts.

2455_2

1. Installation 

a) To apply the edge guard (Item C) to the lower windshield (Item B), find a

clean flat area where you can lay down the windshield.  Partially remove the

protective film on both sides and apply the edge guard using manual pressure

to ensure good adhesion to the windshield. 

                                                                                                                                   2455_1

b) To apply the foam cushion (Item D) to the upper windshield (Item A), find a clean flat area where you can lay down the windshield.  Partially remove the protective film and apply the self adhesive foam cushion using manual pressure to ensure good adhesion to the windshield. 

      2455_2

c) Attach clamps (Item E & F) to the roll cage of your vehicle as per drawings. The 2 lower clamp sets will be used to attach the lower windshield and must be installed with the threaded inserts facing the front of the vehicle. The remaining (2) clamp sets will be used to attach the upper windshield. Install them by ensuring that the threaded inserts are aligned from right to left of the roll cage. Install angle and upper pivot cylinder adaptors to the upper clamps as per drawings. Tighten only the 4 socket cap screws M6 x 45. Do not tighten the clamps to the roll cage at this stage; you will need to make adjustments later on.

                                                                                             2455_5

2455_6

d) To attach pivot components to upper windshield (Item A), as per step a), find a clean flat area where you can lay down the windshield.  Partially remove the protective film where components (Item H & I) are to be attached and follow drawings below.  All screws that are passing through the windshield will be tightened later in step f).   Do not over-tighten the screws that combine the slide arm with the lower pivot, those 2 parts need to swivel. 

2455_7   2455_8

e) Install the lower windshield to all four lower clamps using supplied hardware (Item G) without applying final torque.  Adjust the position of the windshield and tighten all screws with specified torque indicated below.  Ensure that the windshield is perfectly level before tightening.  If the windshield isn’t level, windshield functions will be affected.  Over tightening clamps to roll bar could cause parts failures.   

2455_9   2455_10

f) Attach upper windshield to the machine by following instructions below.
1. Make sure that both upper clamps are at the same height.
2. Hold the upper windshield horizontally and slide it down by ensuring that both upper pivot cylinder adaptors are going through the upper pivot as per drawing #1.

2455_11

3. Pull gently on the windshield as per drawing #2 towards the front of the vehicle for the upper pivot to slide to the end onto the upper pivot cylinder adaptor.

4. Lower the windshield as per drawing #3 and the upper pivot will catch the second upper pivot cylinder adaptor.
5. Adjust the height of the upper clamp first by ensuring the overall leveling.
6. Tighten all screws regarding the upper pivot.
7. Adjust the height of the clamp to the lower pivot and slide arm and use ‘T’ knob to lock in place. Drawing #4 shows the position you should have when windshield is closed.
8. Tighten all remaining screws and nuts.

      2455_12               2455_13

To operate the tilt mechanism:
Simply loosen both ‘T’ knobs (without removing them) and push on the upper windshield from the inside of the cab until the desired position is reached. Then tighten knobs. Note that there are 3 predetermined positions on the slide arm; closed, half-opened and fully-extended.

  •  The tilt mechanism is designed for cooling the airflow in warm temperatures
  •  Note that any open positions are designed for low-speed operation ONLY. 
  •  At high speed riding or when transporting the vehicle, the windshield must be closed.

To remove the upper windshield:
Remove both ‘T’ knobs and follow reverse instructions 4, 3 & 2 of step #f).

2.  Maintenance and Care

Tighten all hardware after first use and periodically thereafter. 

Only registered users can write reviews. Please, log in or register

* Required Fields