Polaris Ranger XP900 / XP1000 and Ranger XP570 Aluminum Roof (Fits: Pro-Fit Cages) by EMP

Polaris Ranger 900/1000/570 Full Size Aluminum Roof (Fits: Pro-Fit Cages) by EMP

EMP is a leader in the Motorsports industry for strong and durable, long lasting Motorsports accessories. Made from nearly 1/8" thick Aluminum and Powder Coated Texture Black making it very light and stylish. Laser Cut and CNC formed in the USA insure a perfect fit. Much lighter than similar steel tops.

Polaris Ranger Aluminum Top Features:

• Bolts to your cage in minutes.
• Made from light Aircraft Grade Aluminum nearly 1/8" Thick (.100").
• Includes: Mounting Hardware and Instructions.
• Laser Cut and CNC Formed insure a perfect fit.
• Gaskets and Foam seal between the top and cage.
• Powder Coated- Texture Black
• Will work with Factory Doors, Windshields, and Cab Back.
• Formed gutter on the front diverts water to the sides.
• Made In Cleveland Ohio.

Ranger XP900 Aluminum Top
                 P/N: EMP-12044
           Fits: 2012 Ranger XP900

Tools Required:
1. 7/16” Wrench
2. 1/2” Wrench
3. 1/2” Socket
4. 3/8” Nut Driver
5. Phillips Screwdriver
6. Cordless Driver
Includes:
1. (1) Aluminum Top
2. (1) Aluminum Rear Brace
3. (3) 1/4” x 1” Self drilling TEK screw
4. (2) 5/16 x 1” Hex Head Flange Bolt
5. (2) 5/16” Flat Washers
6. (4) 5/16” Nylon nut (2 extra)
7. (8) 1/4-20 x 1” Black Truss Head Screw (to attach top)
8. (6) 1/4 ID x 1-1/4” OD Black Washer
9. (8) 1/4 Washers (clear zinc)
10. (10) 1/4 Nylon Nuts
11. (2) 10-32 x 1/2” Black Phillips Screw (used to attach light housing)
12. (1) Square Light Housing (10093-01)
13. (1) Round LED Light
14. (2) 1/8” x 1” x 22-1/2” U-Shaped Edge Trim (for sides)
15. (1) 1/8” x 50” Long Bubble Safety Edge (for front)
16. (2) 1/8”thick x 1” wide x 51” long Adhesive Backed Foam.
17. (2) 1” tall x 1” wide x 30” Long Ad-hesive Backed Foam (#8709K76)
18. (1) Logo Sticker

 Must be installed by a profession-al Technician.
Installation:
Start by prepping the top an rear brace for installation.
1. Stick item #15, 1” wide x 1/8” thick foam to the top front cage brace as shown in figure 1. This will go be-tween the top and cage when fully at-tached.
2. Stick the last item #15 to the rear brace as shown in figure 2.
3. Attach item #14, Safety edge to the front under side as shown in figure 3.
4. Stick item #16, to both sides of the underside of the top as shown in fig-ure 4. This will go between the top and your cage.
5. Slide item #13, U-shaped edge trim over both sides of the top.
6. Put the light in the housing as attach the light and housing to the top with the small Phillips screws.
Now, we are ready to install the top.
1. Attach the rear brace to the rear of your cage with the (3) self tapping screws, (2) 5/16” Bolts, 5/16” nuts, and (1) 1/4” Black Phillips screws. See fig. 7, fig. 8 and fig. 9.
2. Use the remaining 1/4’ x 1’ Black Phillips screws, Large Washers, and 1/4’ nylon nuts to attach the top to the rear brace and cage You will three bolts in the rear brace an three bolts in the front existing holes. The washers will go on top.